locationnsa.blogg.se - Scanner peugeot planet 2000

SCANNER PEUGEOT PLANET 2000 HOW TO
SCANNER PEUGEOT PLANET 2000 PRO
SCANNER PEUGEOT PLANET 2000 CODE
SCANNER PEUGEOT PLANET 2000 WINDOWS

Q9: I install diagbox software on Windows XP3, 32BIT, but it can’t communicate with the car, besides, I install PPS software in another computer (Win XP, 32bit, SP3),

Q8: Would you please store the software lexia3 pp2000 and diagbox7.76 in one CD?Ī8: No, they are not allowed to store in one CD, they have to be stored them in two different CD, otherwise the software installation will get errors. Q6: is PPS compatible with Peugeot 307 HDI?Ī6: PPS2000 work with Peugeot 307, but it is not compatible with Hybrid Diesel Peugeot only with the gasoline car. Q5: Can Lexia-3 (item NO: SP08-C) work with Peugeot Partner Tepee B9 2011 diesel car?Ī5: this car model is included in the supported carlist, so far no users feedback this car is not supported. Q3:after plug the USB cable to the Lexia-3 (item NO. SP08-C), the indicator lights flash and off, off and flash, not stable.Is the USB cable also connected with the car?Ĭheck whether the USB cable is not connected well with the computer.yes, I do. I try on several cars, does not work either.Ī3:try to use another USB cable, if it will not work either, contact us, maybe it needs to return to us for check.Ī4: Yes, it does, but which year of your Peugeot 308? Lexia-3 PP2000 works with Peugeot 308 from 1996 to 2008. Q1: when install Lexia-3 Diagbox software, error message reading “ERROR Lexia: error during installation of Lexia. You have to reactivate to restart the installation.”Ī1: Your computer system isn’t compatible with the software please use Windows XP operation system.Ī2: If your car has Tire pressure control unit, lexia-3 can test the tire pressure. Works with the adapters XS Evolution Lexia3.

SCANNER PEUGEOT PLANET 2000 WINDOWS

System Requirements: Windows XP, 512 MB ?RAMĭealer diagnostic program for car PEUGEOT & CITROEN.

SCANNER PEUGEOT PLANET 2000 HOW TO

How to Solve SVCI 2020 V1.Diagbox V7.83 Software For Lexia-3 PP2000 Diagnostic Tool For Peugeot Citroen.

Mercedes- Benz AKL Programming by Xtool X100 Pad3 (SE) with Xtool M821: Save 65% Calculation Time!.

SCANNER PEUGEOT PLANET 2000 PRO

2022 Newest ThinkCar Pro (Thinkdiag Mini) Download+ Registration+ Activation Guide.How to Clear Diagnostic History on Launch X431 V/V+/PAD VII/PROS….Launch X431 Redownload AutoSearch Software Guide.How to Solve Autel IM608 Missing Remote Function Menu?.Which Tool is Good to Reset AdBlue on Mercedes- Benz?.This is from obd tool website technical support: Peugeot Reading Codes by Lexia 3 PP2000Ĭar Key Programmer Auto Diagnostic Tool Categories Read more about Peugeot scanner, please go to: Throttle Switch Unit (Full Load Position). The “CHECK ENGINE” indicator should be “ON” and all fault codes should have been cleared. Depress the switched jumper for more than 10 seconds.

SCANNER PEUGEOT PLANET 2000 CODE

Perform a test sequence up to a code 11.

To erase the fault code memory turn the ignition switch to the “RUN” (ON) position.

Disconnecting components and wiring harness connectors with the ignition switch in the “RUN” (ON) position may set additional codes and cause permanent damage to the Motronic system. Be sure to disconnect the “switched jumper” and turn the ignition switch to the “OFF” position before attempting repairs.

Repair the indicated faults or repeat the test.

Code 11 signals the end of the test sequence and there are no other codes stored. Refer to the fault code chart. Up to 5 codes may be stored in the fault memory.

Repeat steps 4 and 5 until a code 11 is displayed.

The combination of the (tens)+(units) is the displayed fault code. Take note of all the stored codes. Remember the first set of flash codes is the (tens) and the second set of flash codes is the (units).

Wait for the “CHECK ENGINE” light to come on continuously.

Thus, a code 12 which indicates the beginning of the “TEST” sequence has been displayed. Open the “switched jumper” and the “CHECK ENGINE” indicator will:

Close the switched jumper for 3 seconds. The “CHECK ENGINE”.

Turn the ignition switch to the “RUN” (ON) position.

Connect the other terminal of the switched jumper to a good ground source.

Connect a switched jumper to wire 17 of connector M720 which is the green 2 pin connector.

Here is the instruction on how to do Peugeot codes reading with Lexia-3 PP2000.