- #SOFTRAID 5 SERIALS SERIAL NUMBER#
- #SOFTRAID 5 SERIALS DRIVERS#
- #SOFTRAID 5 SERIALS MANUAL#
- #SOFTRAID 5 SERIALS FULL#
r rounds The number of iterations for the KDF algorithm to use when converting a p passfile Passphrase file used when crypto volumes are brought up. P Change the passphrase on the selected crypto volume. A RAID volume rather than a RAID controller isĮxpected as the device argument.
#SOFTRAID 5 SERIALS FULL#
TheĬhunk must be specified as a full path to a deviceįile (e.g. It would if the disk physically went offline. The state of the RAID volume will change in the same way that O chunk |Ĭhannel: target Set the state of chunk or l chunk Use the chunk device list to create a new volume k keydisk Use special device keydisk as a key disk for aĬrypto volume.
Missing RAID 1C chunks will be marked as offlineĪnd must be rebuilt before they become part of the array again. New volume is created, and a minimum of one chunk when an existing The RAID 1C discipline requires a minimum of two chunks when a The CONCAT discipline requires a minimum of one chunk, RAID 0Īnd RAID 1 disciplines require a minimum of two chunks, RAID 5 requiresĪ minimum of three chunks and the CRYPTO discipline requires exactly one 1C RAID 1 + CRYPTO: An encrypting and mirroring discipline. 5 RAID 5: A striping discipline with floating parity chunk. “softraid0” it supports multiple volumes.Ġ RAID 0: A striping discipline. c raidlevel Create a new softraid(4) volume of level noauto Do not automatically assemble this volume at boot time. May beįorce Force the operation for example, force the creation of volumes with Softraid(4) devices are as follows: -C flag Pass flag to bioctl. In addition to the relevant options listed above, the options for u channel: target Instruct the device at Interval seconds, starting the first iterationĪfter start seconds. auto] Enable the patrol functionality to start/stop automatically in every
#SOFTRAID 5 SERIALS MANUAL#
manual Enable the patrol functionality to start/stop manually. disable Disable the patrol functionality. get Retrieve the current patrol configuration. start Start the patrol on the RAID controller. Stop Stop the patrol on the RAID controller.
t patrol-function Control the RAID card's patrol functionality, if supported. A RAID volume rather than a RAIDĬontroller is expected as the final argument. The offline chunk in the volume it is not possible to change the number Softraid(4), a partition of fstype “RAID”), replacing R chunk |Ĭhannel: target Manually kick off a rebuild of a degraded RAID volume, using
#SOFTRAID 5 SERIALS SERIAL NUMBER#
q Show vendor, product, revision, and serial number for the given disk. In order to reduce the number of digits to four or less. Suffixes: Byte, Kilobyte, Megabyte, Gigabyte, Terabyte, Petabyte, Exabyte h Where necessary, produce “human-readable” output. Is currently marked “Unused”, promote it to being a b channel: target Instruct the device at Given above, or by the first letter only (e.g. Quiet Silence the alarm if it is currently beeping. get Retrieve the current alarm state (enabled or disabled). enable Enable the alarm on the RAID controller. The options for RAID controllers are as follows: -a alarm-function Control the RAID card's alarm functionality, if supported.ĭisable Disable the alarm on the RAID controller. Softraid(4) controller (always softraid0). For operations which will be performed againstĮnclosures, it is also possible to directly specify the enclosure name (e.g. In the first synopsis, RAID controllers are managed.ĭevice specifies either a drive (e.g.
#SOFTRAID 5 SERIALS DRIVERS#
RAID device drivers which support management functionality can RAID management interface SYNOPSIS bioctl
0 kommentar(er)
